- How much drop do you need for sewer line?
- Can a sanitary tee be used horizontally for venting?
- Can you use a wye for venting?
- Can you use a sanitary tee for toilet?
- Can you put a 90 in a sewer line?
- Is 480v Delta or Wye?
- Can sink and toilet shared vent?
- What is the purpose of a sanitary tee?
- What is the difference between a sanitary tee and a Wye?
- What is a Wye?
- Which is better Wye or Delta?
- Can a shower and toilet share the same drain?
- What is a combo Wye?
- Does a sewer line have to be straight?
- Can a double wye be installed horizontally?
- Can you use a wye vertically?
- Is wye connection series or parallel?
- How deep is the sewer line in my yard?
How much drop do you need for sewer line?
You probably know that drains need to flow downhill into your sewer.
But do you know the proper slope.
The ideal slope of any drain line is ¼ inch per foot of pipe.
In other words, for every foot the pipe travels horizontally, it should be dropping ¼ inch vertically..
Can a sanitary tee be used horizontally for venting?
Every trap needs a vent, most are dry (see UPC 908.4 where wet venting allowed) to roof originating from fixture trap arm – see below where you can combine vents – also grading of combination vents. Sanitary tees may only be used on drainage piping when transitioning from horizontal (1/4” per foot) to vertical.
Can you use a wye for venting?
Absolutely! Most any fitting is perfectly acceptable and legal, just don’t use any reducers, caps or traps in the venting.
Can you use a sanitary tee for toilet?
You can’t use a tee, and you must have a vent between the connection and the toilet. Otherwise when another toilet is flushed, and you are sitting on the toilet, the “whoosh” may go the other way and give you a wet surprise.
Can you put a 90 in a sewer line?
If you have to make a 90-degree bend, use two 45-degree fittings and put a small piece of straight pipe between the fittings, if possible. It’s fine to have a larger-radius (sweep) 90-degree bend at the base of a vertical drainage stack where the wastewater starts to travel horizontally.
Is 480v Delta or Wye?
480V 3 Phase Delta is a 3 Wire power configuration and does not include a neutral wire. Most 480V power systems are not a Delta configuration because the phase to ground voltage is 480V or above 300V.
Can sink and toilet shared vent?
(Sinks, tubs, showers all have 1.5 fixtures units each). As a general rule, you will just be able to vent 2 fixtures on a toilet wet vent. … The toilet drain should be 3″, the sink drain is 1.5″, the shared sink drain/toilet vent area should be 2″, and the vent going up should be 1.5″.
What is the purpose of a sanitary tee?
A sanitary tee should be used when connecting a horizontal run, such as a waste arm to a vent stack or vertical riser.
What is the difference between a sanitary tee and a Wye?
Connections to horizontal drain lines should be made with wye (Y) fittings. The fitting called a “Sanitary Tee” looks like it could do the job, but it doesn’t. A sanitary tee cannot be laid on its back, horizontally: It is shaped differently than the wye and should only be aligned vertically, or it may block up.
What is a Wye?
In railroad structures, and rail terminology, a wye (like the ‘Y’ glyph) or triangular junction is a triangular joining arrangement of three rail lines with a railroad switch (set of points) at each corner connecting to each incoming line.
Which is better Wye or Delta?
An advantage of the Delta connection is higher reliability. If one of the three primary windings fails, the secondary will still produce full voltage on all three phases. … An advantage of the Wye connection is that it can provide multiple voltages without the need for additional transformers.
Can a shower and toilet share the same drain?
Here’s the longer answer: Your shower and toilet most likely share a drain line and a vent stack (this setup is called wet venting, more on that later). If either the line or the stack has a clog or blockage, air is forced either up or down your toilet, making the gurgling noise you’re hearing.
What is a combo Wye?
Used to connect a horizontal branch line to a vertical drain pipe in a PVC DWV system.
Does a sewer line have to be straight?
Vent pipes must be installed so they stay dry. This means that they should emerge from the top of the drainpipe, either straight vertically or at no less than a 45-degree angle from horizontal, so that water cannot back up into them.
Can a double wye be installed horizontally?
quote; The double fixture fitting can’t be used on the horizontal. It is NOT a back to back fixture fitting.
Can you use a wye vertically?
This is a sanitary tee and can only be used as shown in the vertical orientation. They are only used to go from the horizontal to vertical plane. If used flat (horizontal) they are prone to clogging. You must use a long sweep or wye+⅛ for horizontal DWV.
Is wye connection series or parallel?
3 transformer coils (windings) wired in WYE configuration : The 3 coils are wired in parallel with each other. Amperage on each line equals amperage on each coil. Phase Voltage between Hot and Neutral is same for each line.
How deep is the sewer line in my yard?
Assess the Sewer Line Problem The depth at which you reach the sewer line will vary. It can be as shallow as 18 to 30 inches or as much as 5 or 6 feet. In cold climates, the pipe will be buried deeper to prevent the pipe from freezing in the winter. But pipe depth is not always a matter of climate.